More Accessories

Product Listing

  • Product Part
    038-00323-07
  • Product Part
    201-35183

    Description: For stainless steel columns and high temperatures (250 °C or higher)

  • Product Part
    201-47616-01

    Description: Quartz Wool (2 g) for packed columns.

  • Product Part
    201-53090
  • Product Part
    201-54321
  • Product Part
    221-08882-91

    Description: For stainless steel columns and GC-2014 models (except TCD)

  • Product Part
    221-10078-92

    Description: Column Connector for WBC and glass packed columns on GC2014-TCD

  • Product Part
    221-10079-93

    Description: Required when connecting stainless steel packed columns on GC2014-TCD

  • Product Part
    221-14087-91

    Description: For Stain Steel column connection, at sample injection unit for GC-14/2014. 5mm x 2mm, M-to-GF, 15 cm Requires Glass insert 221-14093 or 221-14093-84    

  • Product Part
    221-15561-91

    Description: A glass column joint. Two pieces are required. (one for detector and other for injector) Use with Graphite ferrule or O-ring P4.

  • Product Part
    221-34121-94

    Description: For adding a moisture filter to the carrier line

  • Product Part
    221-38102-91

    Description: Press-Tight™ Connector (5 pcs) This connector is used to connect capillary columns easily by inserting the columns into the connector from both ends. When the columns are coated with polyimide resin, the connection will remain tight almost permanently and will be completely free of leakage. Applicable to 0.35 mm to 0.8 mmOD capillary columns. This product is usable up to the maximum temperature of your columns—not to exceed 350 °C. Main usage: Connection of broken capillary columns The connectors are unobtrusive.   On-column sample injection Any capillary columns can be used in on-column injection mode by connecting a short wide-bore capillary columns to the inlet of the column   Retention gap method An about 2 meters long capillary tube with no stationary phase, which is connected to the head of analytical capillary column, prevents peaks from being split  Column conditioning A short capillary tube, which is connected to the outlet of the column, prevents air (oxygen) from diffusing into the column, thus preventing the deterioration of liquid phase which is kept at a high temperature   Stable storing of capillary columns Deterioration by air and contamination can be prevented by connecting the both ends with a capillary tube.

  • Product Part
    221-38102-92

    Description: Press-Tight™ Connector (5 pcs with 5 g polyimide resin) This connector is used to connect capillary columns easily by inserting the columns into the connector from both ends. When the columns are coated with polyimide resin, the connection will remain tight almost permanently and will be completely free of leakage. Applicable to 0.35 mm to 0.8 mmOD capillary columns. This product is usable up to the maximum temperature of your columns—not to exceed 350 °C. Main usage: Connection of broken capillary columns The connectors are unobtrusive.   On-column sample injection Any capillary columns can be used in on-column injection mode by connecting a short wide-bore capillary columns to the inlet of the column   Retention gap method An about 2 meters long capillary tube with no stationary phase, which is connected to the head of analytical capillary column, prevents peaks from being split   Column conditioning A short capillary tube, which is connected to the outlet of the column, prevents air (oxygen) from diffusing into the column, thus preventing the deterioration of liquid phase which is kept at a high temperature   Stable storing of capillary columns Deterioration by air and contamination can be prevented by connecting the both ends with a capillary tube.

  • Product Part
    221-42559-92

    Description: Filter for outgoing gas through split and purge, silica gel

  • Product Part
    221-48600

    Description: Deactivated, acid washed Glass Wool, to be used on glass inlet liners/inserts

  • Product Part
    221-49065-91

    Description: Gold Gasket, 5pcs

  • Product Part
    221-50595-91

    Description: Used to cut a fused silica capillary tube.  

  • Product Part
    225-09146

    Description: Non-acid-washed, borosilicate glass wool. Use to vaporize a sample in an inlet liner prior to introduction to a GC column. Less inert than acid-washed glass wool.   Similar to Restek # 20789

  • Product Part
    227-35017-01

    Description: Fixing tool for connecting column or restrictor to SMI Flow Disc with 227-35018-01 SMI Flow Disc Nuts.

  • Product Part
    227-35021-02

    Description: Pre swage tool for fixing 227-35019-03 SMI Flow Disc Ferrule 0.5MM to column or restrictor.

  • Product Part
    227-35022-01

    Description: Stainless steel tube for connecting SMI Flow Disc and AUX-APC. Use together with SMI Flow Disc Ferrule 227-35019-01

  • Product Part
    APARES-20192

    Description: Produces square, smooth cuts in 1/16-inch tubing. Eliminates tubing distortion. Cuts hard or soft copper, aluminum, brass, stainless steel, Monel alloy, or titanium.

  • Product Part
    APARES-22656

    Description: Features: Measures volumetric flow for gases across a range of 0.5–500 mL/min. NIST traceable calibration. Ex rating (electrical apparatus for explosive gas atmospheres) for hydrogen and related gas types. Accuracy of ± 2.00% of flow reading or ± 0.200 mL/min, whichever is greater. Over-range warning indicator. Auto shutoff feature. Use as a benchtop or handheld unit. Ergonomic design and side grips for comfort. Measures most gas types.* Convenient carrying/storage case included. Uses two AA batteries (included). Data output via USB port. One-year warranty (excludes recalibration). Recalibration service available. *The flowmeter is designed to measure clean, dry, noncorrosive gases. Flowmeter Specifications Type of Flowmeter: Volumetric Battery: 2-AA Operating Temp. Range: 32–120 °F (0–48 °C) Warranty: One-year warranty (excludes recalibration) Certification/Compliance: CE, Ex, Canadian ICES-003, WEEE, RoHS 2, China RoHS 2, UKCA To ensure the most accurate flow measurements, recalibrate your ProFLOW 6000 flowmeter once a year. Prolonged failure to recalibrate your unit may result in increased error.

Showing 1 to 30 of 31