0
0
PLOT columns
-
Description:
Stationary phase: Molecular sieve 5A Easily separate permanent gases at temperatures above ambient. Improve accuracy with sharp, symmetrical peaks for argon, oxygen, and carbon monoxide. Temp. range up to 300 °C Similar phases: HP-PLOT Molesieve, CP-Molsieve 5A, Mol Sieve 5A PLOT
OUT OF STOCKStationary phase: Molecular sieve 5A Easily separate permanent gases at temperatures above ambient. Improve accuracy with sharp, symmetrical peaks for argon, oxygen, and carbon monoxide. Temp. range up to 300 °C Similar phases: HP-PLOT Molesieve, CP-Molsieve 5A, Mol Sieve 5A PLOT
-
Description:
Non-polar PLOT column incorporating 100% divinylbenzene. Excellent for analysis of C1 to C3 hydrocarbons as well as isomers and alkanes up to C12. High retention for CO2 simplifies gas analysis; CO2 and methane separated from O2/N2/CO. (Note: O2/N2/CO not separated at ambient temperature.) Use for analysis of oxygenated compounds and solvents. Similar phases: HP-PLOT Q, CP-PoraPLOT Q, CP-PoraBOND Q, Supel-Q PLOT, Rt-Q-BOND
OUT OF STOCKNon-polar PLOT column incorporating 100% divinylbenzene. Excellent for analysis of C1 to C3 hydrocarbons as well as isomers and alkanes up to C12. High retention for CO2 simplifies gas analysis; CO2 and methane separated from O2/N2/CO. (Note: O2/N2/CO not separated at ambient temperature.) Use for analysis of oxygenated compounds and solvents. Similar phases: HP-PLOT Q, CP-PoraPLOT Q, CP-PoraBOND Q, Supel-Q PLOT, Rt-Q-BOND
-
Description:
KCl deactivation Lowest polarity alumina column in Shimadzu PLOT columns. Low moisture sensitivity reduces the need for frequent regeneration. Acetylene elutes before n-butane. Methyl acetylene (impurity in 1,3-butadiene) elutes before 1,3-butadiene. Similar phases: GS-Alumina KCl, HP-PLOT Al2O3 KCl, CP-Al2O3/KCl, Alumina chloride PLOT, Rt-Alumina BOND/KCl
OUT OF STOCKKCl deactivation Lowest polarity alumina column in Shimadzu PLOT columns. Low moisture sensitivity reduces the need for frequent regeneration. Acetylene elutes before n-butane. Methyl acetylene (impurity in 1,3-butadiene) elutes before 1,3-butadiene. Similar phases: GS-Alumina KCl, HP-PLOT Al2O3 KCl, CP-Al2O3/KCl, Alumina chloride PLOT, Rt-Alumina BOND/KCl
-
Description:
SS-Alumina-MAPD is an alumina column focused specifically on the separation of the peaks from methylacetylene to propadiene (MAPD). This column has strong heat resistance, so it can be used up to 200 °C and can perform hydrocarbon analysis up to C10. In addition, it has excellent stability and minimizes the retention time fluctuation due to moisture. It shows high selectivity for C1 to C5 hydrocarbons at ppm level. Since the alumina oxide adsorbent is fixed to the inner wall of the column, there is no need to worry about particle exfoliation.
OUT OF STOCKSS-Alumina-MAPD is an alumina column focused specifically on the separation of the peaks from methylacetylene to propadiene (MAPD). This column has strong heat resistance, so it can be used up to 200 °C and can perform hydrocarbon analysis up to C10. In addition, it has excellent stability and minimizes the retention time fluctuation due to moisture. It shows high selectivity for C1 to C5 hydrocarbons at ppm level. Since the alumina oxide adsorbent is fixed to the inner wall of the column, there is no need to worry about particle exfoliation.
-
Description:
SS-Alumina-MAPD is an alumina column focused specifically on the separation of the peaks from methylacetylene to propadiene (MAPD). This column has strong heat resistance, so it can be used up to 200 °C and can perform hydrocarbon analysis up to C10. In addition, it has excellent stability and minimizes the retention time fluctuation due to moisture. It shows high selectivity for C1 to C5 hydrocarbons at ppm level. Since the alumina oxide adsorbent is fixed to the inner wall of the column, there is no need to worry about particle exfoliation.
OUT OF STOCKSS-Alumina-MAPD is an alumina column focused specifically on the separation of the peaks from methylacetylene to propadiene (MAPD). This column has strong heat resistance, so it can be used up to 200 °C and can perform hydrocarbon analysis up to C10. In addition, it has excellent stability and minimizes the retention time fluctuation due to moisture. It shows high selectivity for C1 to C5 hydrocarbons at ppm level. Since the alumina oxide adsorbent is fixed to the inner wall of the column, there is no need to worry about particle exfoliation.
-
Description:
SS-Alumina-MAPD is an alumina column focused specifically on the separation of the peaks from methylacetylene to propadiene (MAPD). This column has strong heat resistance, so it can be used up to 200 °C and can perform hydrocarbon analysis up to C10. In addition, it has excellent stability and minimizes the retention time fluctuation due to moisture. It shows high selectivity for C1 to C5 hydrocarbons at ppm level. Since the alumina oxide adsorbent is fixed to the inner wall of the column, there is no need to worry about particle exfoliation.
OUT OF STOCKSS-Alumina-MAPD is an alumina column focused specifically on the separation of the peaks from methylacetylene to propadiene (MAPD). This column has strong heat resistance, so it can be used up to 200 °C and can perform hydrocarbon analysis up to C10. In addition, it has excellent stability and minimizes the retention time fluctuation due to moisture. It shows high selectivity for C1 to C5 hydrocarbons at ppm level. Since the alumina oxide adsorbent is fixed to the inner wall of the column, there is no need to worry about particle exfoliation.
-
Description:
SS-Alumina-KCL has strong heat resistance, so, it can be used up to 200 °C and is capable of hydrocarbon analysis up to C10. In addition, it has excellent stability and minimizes the retention time fluctuation due to moisture. It shows high selectivity for C1 to C5 hydrocarbons at ppm level. Since the alumina oxide adsorbent is fixed to the inner wall of the column, there is no need to worry about particle exfoliation. A column with a particle trap column (SS-Alumina-KCL-PT) is recommended when connected to MS detector. SS-Alumina-KCL-UMetal uses inactivated metal capillary that are resistant to physical impact, making the column easier to handle than fused silica capillary column.
OUT OF STOCKSS-Alumina-KCL has strong heat resistance, so, it can be used up to 200 °C and is capable of hydrocarbon analysis up to C10. In addition, it has excellent stability and minimizes the retention time fluctuation due to moisture. It shows high selectivity for C1 to C5 hydrocarbons at ppm level. Since the alumina oxide adsorbent is fixed to the inner wall of the column, there is no need to worry about particle exfoliation. A column with a particle trap column (SS-Alumina-KCL-PT) is recommended when connected to MS detector. SS-Alumina-KCL-UMetal uses inactivated metal capillary that are resistant to physical impact, making the column easier to handle than fused silica capillary column.
-
Description:
SS-Alumina-KCL has strong heat resistance, so, it can be used up to 200 °C and is capable of hydrocarbon analysis up to C10. In addition, it has excellent stability and minimizes the retention time fluctuation due to moisture. It shows high selectivity for C1 to C5 hydrocarbons at ppm level. Since the alumina oxide adsorbent is fixed to the inner wall of the column, there is no need to worry about particle exfoliation. A column with a particle trap column (SS-Alumina-KCL-PT) is recommended when connected to MS detector. SS-Alumina-KCL-UMetal uses inactivated metal capillary that are resistant to physical impact, making the column easier to handle than fused silica capillary column.
OUT OF STOCKSS-Alumina-KCL has strong heat resistance, so, it can be used up to 200 °C and is capable of hydrocarbon analysis up to C10. In addition, it has excellent stability and minimizes the retention time fluctuation due to moisture. It shows high selectivity for C1 to C5 hydrocarbons at ppm level. Since the alumina oxide adsorbent is fixed to the inner wall of the column, there is no need to worry about particle exfoliation. A column with a particle trap column (SS-Alumina-KCL-PT) is recommended when connected to MS detector. SS-Alumina-KCL-UMetal uses inactivated metal capillary that are resistant to physical impact, making the column easier to handle than fused silica capillary column.
-
Description:
SS-Alumina-KCL has strong heat resistance, so, it can be used up to 200 °C and is capable of hydrocarbon analysis up to C10. In addition, it has excellent stability and minimizes the retention time fluctuation due to moisture. It shows high selectivity for C1 to C5 hydrocarbons at ppm level. Since the alumina oxide adsorbent is fixed to the inner wall of the column, there is no need to worry about particle exfoliation. A column with a particle trap column (SS-Alumina-KCL-PT) is recommended when connected to MS detector. SS-Alumina-KCL-UMetal uses inactivated metal capillary that are resistant to physical impact, making the column easier to handle than fused silica capillary column.
OUT OF STOCKSS-Alumina-KCL has strong heat resistance, so, it can be used up to 200 °C and is capable of hydrocarbon analysis up to C10. In addition, it has excellent stability and minimizes the retention time fluctuation due to moisture. It shows high selectivity for C1 to C5 hydrocarbons at ppm level. Since the alumina oxide adsorbent is fixed to the inner wall of the column, there is no need to worry about particle exfoliation. A column with a particle trap column (SS-Alumina-KCL-PT) is recommended when connected to MS detector. SS-Alumina-KCL-UMetal uses inactivated metal capillary that are resistant to physical impact, making the column easier to handle than fused silica capillary column.
-
Description:
SS-Alumina-KCL has strong heat resistance, so, it can be used up to 200 °C and is capable of hydrocarbon analysis up to C10. In addition, it has excellent stability and minimizes the retention time fluctuation due to moisture. It shows high selectivity for C1 to C5 hydrocarbons at ppm level. Since the alumina oxide adsorbent is fixed to the inner wall of the column, there is no need to worry about particle exfoliation. A column with a particle trap column (SS-Alumina-KCL-PT) is recommended when connected to MS detector. SS-Alumina-KCL-UMetal uses inactivated metal capillary that are resistant to physical impact, making the column easier to handle than fused silica capillary column.
OUT OF STOCKSS-Alumina-KCL has strong heat resistance, so, it can be used up to 200 °C and is capable of hydrocarbon analysis up to C10. In addition, it has excellent stability and minimizes the retention time fluctuation due to moisture. It shows high selectivity for C1 to C5 hydrocarbons at ppm level. Since the alumina oxide adsorbent is fixed to the inner wall of the column, there is no need to worry about particle exfoliation. A column with a particle trap column (SS-Alumina-KCL-PT) is recommended when connected to MS detector. SS-Alumina-KCL-UMetal uses inactivated metal capillary that are resistant to physical impact, making the column easier to handle than fused silica capillary column.
-
Description:
SS-Alumina-KCL has strong heat resistance, so, it can be used up to 200 °C and is capable of hydrocarbon analysis up to C10. In addition, it has excellent stability and minimizes the retention time fluctuation due to moisture. It shows high selectivity for C1 to C5 hydrocarbons at ppm level. Since the alumina oxide adsorbent is fixed to the inner wall of the column, there is no need to worry about particle exfoliation. A column with a particle trap column (SS-Alumina-KCL-PT) is recommended when connected to MS detector. SS-Alumina-KCL-UMetal uses inactivated metal capillary that are resistant to physical impact, making the column easier to handle than fused silica capillary column.
OUT OF STOCKSS-Alumina-KCL has strong heat resistance, so, it can be used up to 200 °C and is capable of hydrocarbon analysis up to C10. In addition, it has excellent stability and minimizes the retention time fluctuation due to moisture. It shows high selectivity for C1 to C5 hydrocarbons at ppm level. Since the alumina oxide adsorbent is fixed to the inner wall of the column, there is no need to worry about particle exfoliation. A column with a particle trap column (SS-Alumina-KCL-PT) is recommended when connected to MS detector. SS-Alumina-KCL-UMetal uses inactivated metal capillary that are resistant to physical impact, making the column easier to handle than fused silica capillary column.
-
Description:
SS-Alumina-KCL has strong heat resistance, so, it can be used up to 200 °C and is capable of hydrocarbon analysis up to C10. In addition, it has excellent stability and minimizes the retention time fluctuation due to moisture. It shows high selectivity for C1 to C5 hydrocarbons at ppm level. Since the alumina oxide adsorbent is fixed to the inner wall of the column, there is no need to worry about particle exfoliation. A column with a particle trap column (SS-Alumina-KCL-PT) is recommended when connected to MS detector. SS-Alumina-KCL-UMetal uses inactivated metal capillary that are resistant to physical impact, making the column easier to handle than fused silica capillary column.
OUT OF STOCKSS-Alumina-KCL has strong heat resistance, so, it can be used up to 200 °C and is capable of hydrocarbon analysis up to C10. In addition, it has excellent stability and minimizes the retention time fluctuation due to moisture. It shows high selectivity for C1 to C5 hydrocarbons at ppm level. Since the alumina oxide adsorbent is fixed to the inner wall of the column, there is no need to worry about particle exfoliation. A column with a particle trap column (SS-Alumina-KCL-PT) is recommended when connected to MS detector. SS-Alumina-KCL-UMetal uses inactivated metal capillary that are resistant to physical impact, making the column easier to handle than fused silica capillary column.