0
0
- Home
- Technique Categories
Technique Categories
Product Listing
-
-
-
-
Product PartDescription:
Replacement filters for In-line HPLC/UHPLC Precolumn Filters and Direct Connect HPLC/UHPLC Precolumn Filters. Replacement filter for 226-50001-79.
OUT OF STOCKReplacement filters for In-line HPLC/UHPLC Precolumn Filters and Direct Connect HPLC/UHPLC Precolumn Filters. Replacement filter for 226-50001-79.
-
Product PartDescription:
Frit Porosity: 0.2 micron Pressure Rating: 18,000 PSI (0.062" dia. and 0.125" dia.), 10,000 PSI (0.188" dia.) Dead Volume: 1.8 µL (0.062" dia.), 3.5 µL (0.125" dia.), 7.3 µL (0.188" dia.) Frit Material: 316 Stainless Steel Port: 10-32 Port (1/16" CPI) Male Threads: 10-32 Threads In high throughput and routine HPLC separations where mobile phase and sample contamination cause a decrease in column performance or premature column failure, this Pre-column filter will maintain the efficiency of high perfrmance columns and ensure a negligible loss of resolution. This filter can be finger tighten, then wrench tighten an additional 1/4 - 1/2 turn.
OUT OF STOCKFrit Porosity: 0.2 micron Pressure Rating: 18,000 PSI (0.062" dia. and 0.125" dia.), 10,000 PSI (0.188" dia.) Dead Volume: 1.8 µL (0.062" dia.), 3.5 µL (0.125" dia.), 7.3 µL (0.188" dia.) Frit Material: 316 Stainless Steel Port: 10-32 Port (1/16" CPI) Male Threads: 10-32 Threads In high throughput and routine HPLC separations where mobile phase and sample contamination cause a decrease in column performance or premature column failure, this Pre-column filter will maintain the efficiency of high perfrmance columns and ensure a negligible loss of resolution. This filter can be finger tighten, then wrench tighten an additional 1/4 - 1/2 turn.
-
Product PartDescription:
Frit Porosity: 2 micron Pressure Rating: 18,000 PSI (0.062" dia. and 0.125" dia.), 10,000 PSI (0.188" dia.) Dead Volume: 2.1 µL (0.062" dia.), 5.2 µL (0.125" dia.), 11.3 µL (0.188" dia.) Frit Material: 316 Stainless Steel Port: 10-32 Port (1/16" CPI) Male Threads: 10-32 Threads
OUT OF STOCKFrit Porosity: 2 micron Pressure Rating: 18,000 PSI (0.062" dia. and 0.125" dia.), 10,000 PSI (0.188" dia.) Dead Volume: 2.1 µL (0.062" dia.), 5.2 µL (0.125" dia.), 11.3 µL (0.188" dia.) Frit Material: 316 Stainless Steel Port: 10-32 Port (1/16" CPI) Male Threads: 10-32 Threads
-
Product PartDescription:
Frit Porosity: 2 micron Pressure Rating: 18,000 PSI (0.062" dia. and 0.125" dia.), 10,000 PSI (0.188" dia.) Dead Volume: 2.1 µL (0.062" dia.), 5.2 µL (0.125" dia.), 11.3 µL (0.188" dia.) Frit Material: 316 Stainless Steel Port: 10-32 Port (1/16" CPI) Male Threads: 10-32 Threads
OUT OF STOCKFrit Porosity: 2 micron Pressure Rating: 18,000 PSI (0.062" dia. and 0.125" dia.), 10,000 PSI (0.188" dia.) Dead Volume: 2.1 µL (0.062" dia.), 5.2 µL (0.125" dia.), 11.3 µL (0.188" dia.) Frit Material: 316 Stainless Steel Port: 10-32 Port (1/16" CPI) Male Threads: 10-32 Threads
-
Product PartDescription:
Pressure rated up to 25,000 psi (1,720 bar) Capable of up to ten repeat assembly cycles with no impact on pressure holding ability or carry-over; Available in multiple threaded configurations for use with 1/16 in (1.6 mm) and 1/32 in (0.79 mm) OD tubing Materials of construction: Stainless Steel and Proprietary PEEK™ polymer blend (PK) The fittings are reusable when following the proper tightening torque specification. With a polymer front ferrule, there is no damage to the tubing or receiving port, also increasing the life of these components.
OUT OF STOCKPressure rated up to 25,000 psi (1,720 bar) Capable of up to ten repeat assembly cycles with no impact on pressure holding ability or carry-over; Available in multiple threaded configurations for use with 1/16 in (1.6 mm) and 1/32 in (0.79 mm) OD tubing Materials of construction: Stainless Steel and Proprietary PEEK™ polymer blend (PK) The fittings are reusable when following the proper tightening torque specification. With a polymer front ferrule, there is no damage to the tubing or receiving port, also increasing the life of these components.
-
Product PartDescription:
Pressure rated up to 25,000 psi (1,720 bar) Capable of up to ten repeat assembly cycles with no impact on pressure holding ability or carry-over; Available in multiple threaded configurations for use with 1/16 in (1.6 mm) and 1/32 in (0.79 mm) OD tubing Materials of construction: Stainless Steel and Proprietary PEEK™ polymer blend (PK) The fittings are reusable when following the proper tightening torque specification. With a polymer front ferrule, there is no damage to the tubing or receiving port, also increasing the life of these components.
OUT OF STOCKPressure rated up to 25,000 psi (1,720 bar) Capable of up to ten repeat assembly cycles with no impact on pressure holding ability or carry-over; Available in multiple threaded configurations for use with 1/16 in (1.6 mm) and 1/32 in (0.79 mm) OD tubing Materials of construction: Stainless Steel and Proprietary PEEK™ polymer blend (PK) The fittings are reusable when following the proper tightening torque specification. With a polymer front ferrule, there is no damage to the tubing or receiving port, also increasing the life of these components.
-
Product Part
